AirO is intended for technical and not-too-technical owners of Wi-Fi capable Android devices. It displays the health of the Wi-Fi (“Local Area”) connection, and measures the characteristics of a “Wide Area” connection to a server deeper in the network. It can be used to answer questions like:
• What’s wrong with my Wi-Fi today?
• How strong is my Wi-Fi signal?
• Is there evidence of wireless interference?
• Is the problem in the Wi-Fi connection, or out on the Internet (or corporate network)?
• Is the overall connection to the data center good enough to run my corporate apps?
For an admin guide, including instructions on setting up your Aruba network so mDNS (AirGroup) automatically configures target addresses for AirWave and iPerf servers (allowing the app as downloaded to work on different networks without user interverntion) see the Air Observer Admin Guide hosted on the Aruba Airheads Community web page http://community.arubanetworks.com/t5/Aruba-Apps/New-Admin-Guide-for-the-AirO-Air-Observer-app/td-p/229749 (or go to community.arubanetworks.com and search for "AirO").
The top “Wi-Fi and Local Area Network” section of the screen displays three measurements that show the health of the Wi-Fi connection:
• Signal Strength or RSSI in dBm
We measure signal strength first because if it’s poor, there is no chance of getting a good connection. The remedy, in simple terms, is to get closer to the access point.
• Link Speed.
The usual cause of low link speeds is poor signal strength. But sometimes, even when signal strength is good, interference on the air from Wi-Fi and non-Wi-Fi sources reduces link speeds.
• Ping. This is the familiar ICMP echo test to the network’s default gateway.
A low link speed will often cause long ping times. If link speeds are good but pings slow, it may be a long way to the default gateway over a narrow broadband connection.
The lower section of the screen displays results from tests between the device and a server computer, usually in the corporate data center or on the Internet. The address of this server is chosen from a number configured in ‘settings' – but once chosen, only one server address is used for these tests.
• Ping. There is a ping measurement to this server. It is the same ping test as above, but because this one goes farther it will normally (but not always) take longer. Again, 20msec would be fast and 500 msec would be slow.
Some networks may block ICMP (ping) traffic. In this case, the Wide Area Network ping test will always fail, but normal (e.g. Web) traffic may pass.
• Speedtest. The next tests are ‘speedtests’. For this, we use the iPerf function (iPerf v2). In a corporate context, this should be an iPerf server instance set up somewhere in the core of the network, probably a data center. Because it is a (TCP) throughput test, the figures here will never be more than about 50% of the ‘link speed’ figure for the Wi-Fi connection. The iPerf client in the app is configured to run in bidirectional mode, first an upstream test then downstream.
AIRO è destinato per i proprietari di tecnici e non-troppo-tecniche dei dispositivi Android in grado Wi-Fi. Esso mostra la salute del Wi-Fi ("locale") di connessione e misura le caratteristiche di una connessione "Wide Area" ad un server più profonda nella rete. Può essere utilizzato per rispondere a domande come:
• Cosa c'è di sbagliato con il mio Wi-Fi oggi?
• Quanto è forte il segnale mio Wi-Fi?
• C'è evidenza di interferenza wireless?
• Il problema nella connessione Wi-Fi, o su Internet (o alla rete aziendale)?
• Il collegamento globale per il centro abbastanza buono per eseguire le mie applicazioni aziendali di dati?
Per una guida amministratore, comprese le istruzioni su come configurare la rete in modo da Aruba mDNS (AirGroup) configura automaticamente gli indirizzi di destinazione per i server Airwave e iperf (che consentono l'applicazione come scaricata per lavorare su reti diverse senza interverntion dell'utente) vedere la Admin Guide Air Observer ospitato su la pagina web Aruba Airheads Community http://community.arubanetworks.com/t5/Aruba-Apps/New-Admin-Guide-for-the-AirO-Air-Observer-app/td-p/229749 (O andare a community.arubanetworks.com e cercare "AIRO").
Il top "Wi-Fi e Local Area Network" sezione dello schermo visualizza tre misurazioni che mostrano la salute della connessione Wi-Fi:
• Potenza del segnale o RSSI in dBm
Misuriamo la potenza del segnale in primo luogo perché se è povera, non vi è alcuna possibilità di ottenere una buona connessione. Il rimedio, in termini semplici, è di avvicinarsi al punto di accesso.
• Link Speed.
La causa della velocità di collegamento a bassa è scarsa potenza del segnale. Ma a volte, anche quando la potenza del segnale è buono, le interferenze in onda da Wi-Fi e le fonti non-Wi-Fi riduce velocità di collegamento.
• Ping. Questo è il familiare ICMP echo test al gateway predefinito della rete.
Una velocità di collegamento a bassa spesso causare tempi di ping lunghi. Se la velocità di collegamento sono buone, ma ping lento, può essere un lungo cammino per il gateway predefinito tramite una connessione a banda larga stretta.
La parte inferiore dello schermo visualizza il risultato di test tra il dispositivo e un computer server, di solito nel data center aziendale o su Internet. L'indirizzo di questo server è scelto da un numero configurato in "Impostazioni" - ma una volta scelta, un solo indirizzo del server viene utilizzato per questi test.
• Ping. C'è una misura ping al server. Lo stesso test ping come sopra, ma perché questo va oltre sarà normalmente (ma non sempre) richiedere più. Ancora una volta, 20msec sarebbe veloce e 500 msec sarebbe lento.
Alcune reti potrebbero bloccare ICMP (ping) traffico. In questo caso, il test ping Area Network Ampia fallirà sempre, ma normale (ad esempio, Web), il traffico può passare.
• Speedtest. I prossimi test sono 'speedtests. Per questo, si usa la funzione iperf (iperf v2). In un contesto aziendale, questo dovrebbe essere un'istanza di server iperf costituito da qualche parte nel centro della rete, probabilmente un centro dati. Perché si tratta di un (TCP) di throughput di prova, le cifre qui non saranno mai più di circa il 50% della cifra 'velocità di collegamento' per la connessione Wi-Fi. Il cliente iperf in app è configurato per l'esecuzione in modalità bidirezionale, prima un test di monte poi a valle.